Anzahl Durchsuchen:0 Autor:Site Editor veröffentlichen Zeit: 2019-07-02 Herkunft:Powered
Schneidfähigkeit und Parameter der Hypertherm-Plasmaquelle
Hypertherm | Metall | Dicke (mm) | Strom (A) | Geschwindigkeit (mm/min) | Gegebene Spannung (v) | Abstand zwischen Brenner und Material | Luftdruck (mpa) | Pierce-Zeit (s) | Schnittfugenbreite mm |
45A
| cs | 1mm | 45 | 8000 | 115 | 3,8 mm | 0.5 | 0.1 | 1.1 |
2mm | 45 | 7500 | 117 | 3,8 mm | 0.5 | 0.1 | 1.4 | ||
3mm | 45 | 4000 | 117 | 3,8 mm | 0.5 | 0.3 | 1.5 | ||
5mm | 45 | 2200 | 118 | 3,8 mm | 0.6 | 0.5 | 1.6 | ||
6mm | 45 | 1500 | 120 | 3,8 mm | 0.6 | 0.6 | 1.7 | ||
ss | 1mm | 45 | 7500 | 112 | 3,8 mm | 0.6 | 0.1 | 1.1 | |
2mm | 45 | 7000 | 118 | 3,8 mm | 0.6 | 0.2 | 1.5 | ||
3mm | 45 | 3800 | 120 | 3,8 mm | 0.6 | 0.3 | 1.6 | ||
5mm | 45 | 2000 | 123 | 3,8 mm | 0.6 | 0.5 | 1.7 | ||
6mm | 45 | 1200 | 124 | 3,8 mm | 0.6 | 0.6 | 1.8 | ||
Hypertherm | Metall | Dicke (mm) | Strom (A) | Geschwindigkeit (mm/min) | Gegebene Spannung (v) | Abstand zwischen Brenner und Material | Luftdruck (mpa) | Pierce-Zeit (s) | Schnittfugenbreite mm |
65A | cs | 2mm | 65 | 6500 | 124 | 3,8 mm | 0.6 | 0.2 | 1.6 |
3mm | 65 | 5500 | 125 | 3,8 mm | 0.6 | 0.3 | 1.6 | ||
4mm | 65 | 4500 | 125 | 3,8 mm | 0.6 | 0.5 | 1.7 | ||
6mm | 65 | 3000 | 127 | 3,8 mm | 0.6 | 0.5 | 1.8 | ||
8mm | 65 | 2000 | 129 | 3,8 mm | 0.6 | 0.5 | 1.9 | ||
10mm | 65 | 1300 | 131 | 4,5 mm | 0.6 | 0.7 | 2.0 | ||
12mm | 65 | 900 | 134 | 4,5 mm | 0.6 | 1.2 | 2.2 | ||
ss | 2mm | 65 | 6500 | 125 | 3,8 mm | 0.6 | 0.2 | 1.4 | |
3mm | 65 | 5500 | 125 | 3,8 mm | 0.6 | 0.3 | 1.5 | ||
4mm | 65 | 4500 | 125 | 3,8 mm | 0.6 | 0.5 | 1.6 | ||
6mm | 65 | 2500 | 126 | 3,8 mm | 0.6 | 0.5 | 1.8 | ||
8mm | 65 | 1600 | 129 | 3,8 mm | 0.6 | 0.7 | 1.9 | ||
10mm | 65 | 1000 | 132 | 4,5 mm | 0.6 | 0.7 | 2.0 | ||
12mm | 65 | 800 | 135 | 4,5 mm | 0.6 | 1.2 | 2.2 | ||
Hypertherm | Metall | Dicke (mm) | Strom (A) | Geschwindigkeit (mm/min) | Gegebene Spannung (v) | Abstand zwischen Brenner und Material | Luftdruck (mpa) | Pierce-Zeit (s) | Schnittfugenbreite mm |
85A | cs | 3mm | 85 | 7000 | 122 | 3.8 | 0.6 | 0.3 | 1.7 |
4mm | 85 | 6000 | 122 | 3.8 | 0.6 | 0.3 | 1.7 | ||
6mm | 85 | 4000 | 123 | 3.8 | 0.6 | 0.5 | 1.8 | ||
8mm | 85 | 2800 | 125 | 3.8 | 0.6 | 0.5 | 1.9 | ||
10mm | 85 | 1800 | 127 | 3.8 | 0.6 | 0.5 | 2.0 | ||
12mm | 85 | 1300 | 130 | 4.5 | 0.6 | 0.7 | 2.2 | ||
16mm | 85 | 900 | 134 | 4.5 | 0.6 | 1.0 | 2.4 | ||
ss | 3mm | 85 | 7000 | 122 | 3.8 | 0.6 | 0.3 | 1.6 | |
4mm | 85 | 6000 | 122 | 3.8 | 0.6 | 0.3 | 1.7 | ||
6mm | 85 | 4000 | 122 | 3.8 | 0.6 | 0.5 | 1.8 | ||
8mm | 85 | 2500 | 124 | 3.8 | 0.6 | 0.5 | 1.9 | ||
10mm | 85 | 1600 | 127 | 4.5 | 0.6 | 0.7 | 2.1 | ||
12mm | 85 | 1100 | 131 | 4.5 | 0.6 | 0.7 | 2.3 | ||
Hypertherm | Metall | Dicke (mm) | Strom (A) | Geschwindigkeit (mm/min) | Gegebene Spannung (v) | Abstand zwischen Brenner und Material | Luftdruck (mpa) | Pierce-Zeit (s) | Schnittfugenbreite mm |
105A | cs | 6 | 105 | 4500 | 144 | 6.4 | 0.6 | 0.5 | 2.1 |
8 | 105 | 3500 | 145 | 6.4 | 0.6 | 0.8 | 2.2 | ||
10 | 105 | 2500 | 145 | 6.4 | 0.6 | 0.8 | 2.2 | ||
12 | 105 | 1800 | 145 | 6.4 | 0.6 | 0.8 | 2.2 | ||
16 | 105 | 1100 | 149 | 6.4 | 0.6 | 1.0 | 2.5 | ||
20 | 105 | 800 | 152 | 6.4 | 0.6 | 1.0 | 2.7 | ||
ss | 6mm | 105 | 5000 | 139 | 6.4 | 0.6 | 0.5 | 2.1 | |
8mm | 105 | 3800 | 141 | 6.4 | 0.6 | 0.5 | 2.3 | ||
10mm | 105 | 2300 | 144 | 6.4 | 0.6 | 0.6 | 2.4 | ||
12mm | 105 | 1500 | 148 | 6.4 | 0.6 | 0.8 | 2.5 | ||
16mm | 105 | 1000 | 149 | 6.4 | 0.6 | 0.8 | 2.7 | ||
20mm | 105 | 700 | 154 | 8.0 | 0.6 | 1.25 | 2.9 |